How to erect cages for rabbits with your own hands?

Contents: [hide]

  • Step-by-step construction of
  • What size should a house be?
  • Choose the right material
  • Professional tips

To do the breeding of rabbits, the first thing you need is to build a home for them. The easiest way is to make

cages for rabbits with your own hands. To begin with, the host must determine the place for the cells. If you have not been involved in similar buildings before and do not know how to make a rabbit cage with your own hands, pay attention to the following points. The cage can be built directly on the street or in the room, for example, in a shed or garage. A cage for rabbits, whose drawings can be made on their own, need to be built immediately at large, as these animals will multiply rapidly and there will be a need for a division of females from males.

How to erect cages for rabbits with your own hands?

Draw a single-section cage for rabbits.

It is often necessary to build a cage with its own hands where rabbits are bred for agricultural purposes( for meat and furs).In such conditions, the owners are often interested in the constant reproduction of animals, so there should be a lot of cells. Decorative rabbits in apartments, the owners buy special ready-made cells with all the equipment necessary for housing the animal. The sizes of cages for rabbits always depend on their breed. Consider how to build a cage for your rabbits with your own hands.

Phased construction of

Production of cages for rabbits with its own hands - the process is simple. You need to choose a suitable place for construction. It should be protected from strong winds, draft, burning sun. Such a place may be a barn, garage or part of a plot located in the shade. Often, homeowners set up cells under the shade of grapes.

How to erect cages for rabbits with your own hands?

Figure 1. Scheme of a two-section cage for rabbits.

Then you need to decide on the kind of future cage for rabbits. The cells can be:

  • One-sectional. These are street cells that will protect the animals well from wind and bad weather.
  • Two-sectional. They are well built indoors, it is convenient to grow a large number of rabbits.
  • Three-sectional. This breeding house involves a large number of rabbits, separated by cells: pregnant women, females, males, children. The house can provide for a place for a gaming zone or a walk.
  • To build we choose the most common and often encountered option for construction - the manufacture of a two-section cage for rabbits with his own hands. It will consist of two tiers, or two floors.

    Back to contents

    What size should be the house?

    Now we determine the size. In order to correctly identify them, it is necessary to understand, for individuals of which sizes we build: giant, dwarf or common breeds. Consider the cell size for medium breeds of rabbits. Be sure to make a cage on uplifting floors, otherwise it is possible to penetrate the house for a rabbit of other animals.

    How to erect cages for rabbits with your own hands?

    Figure 2. Two-section cage for rabbits on the side.

    The average height of the first level should be 45 cm from the ground. If we build a multistory house, then from the ground up to 2 floors will be about 95 cm, and to the third one - 1.5 m. The length of the cell depends on the number of individuals living there and their sizes - on average, it is from 1.2 m to 1.5The width of each of the two compartments is 65-80 cm, the height of the front wall is 40-55 cm, the height of the rear wall should be 30 to 45 cm. For ease of construction, it is necessary to draw drawings of the future cage for the rabbits with their own hands.

    We propose to build a large two-section cage for adult rabbits in 2 tiers to save space. The diagram you see in Figure 1 shows that the height of the two-sectional cell will be 2.0-2.2 m, width - 140 cm, depth - 60 cm. The depth is clearly seen in Figure 2.

    It is imperative that a large cage should stand on legs at a height of 50-70 cm. In the rabbit there will be 2 cells, each length of 70 cm. Between the cells should be a partition in the form of a feeder for the hay, on the sides - holes for the grain. Each of the cells will be on the front wall to have a height of 60 cm, between the tiers - 30 cm on the front wall and 40 cm in the back. The corner roof will go downwards, which will reduce the height of the rear wall by 10 cm. According to tables 1 and 2, the size of the future rabbit is very well visible. Below in the tables are the drawings for future two-part pebbles.

    Return to contents

    Choose appropriate material

    How to erect cages for rabbits with your own hands?

    Cage sketches for rabbits with rabbits.

    The next step will be a selection of construction materials for building a cell. Typically, cells are constructed of wooden beams and sheet plywood, and a grid may also fit. It is better to make the roof of a tree, only to cover the top with a plywood or wavy slipper.

    For walls, cells choose very dense wood to avoid draft, for the floor fit smooth boards of 20 cm without gaps. For the doors you need to buy a grid. On the roof must make a speaker for a visor, which will protect the animals from rain and snow.

    We prepare construction equipment: hammer, nails, screws, screwdrivers, metal scissors, tape measure, saw blade, Bulgarian.

    Building materials for the rabbit: wooden well-dried skeleton bars, roof slate, rack mesh with small frame cells( 20x20 mm or 25x25 mm).For the separator of the feeder choose grids of a large size, so that the hay can be more easily pulled out. For the bottom of the cage we will take wooden rails, for the rear wall of the rabbit, you need a whole board or large plywood.

    Having taken the right building material and drawing of a cage, building a house for rabbits under the finished scheme will be easy.

    How to erect cages for rabbits with your own hands?

    Tools for making rabbit cages.

  • We cut wooden rails for frame in the size of the drawing and fasten with screws.
  • Plywood sheets for the back walls are also better cut and attached to the rear walls to leave the frame. Here you see a finished two-section bunk squad of wooden rails.
  • Next, we are laying the net floor in the crevices, necessarily having correctly measured the grid. It is stretched and secured by screws. On top of the grid, wooden rails for the floor are attached to the edges with screws. Why is not the whole wooden flooring used? Because the animals will go to the toilet, and the tree absorbs the liquid very well. Therefore, the floor of the rails will quickly deteriorate, it will pass urine and feces.
  • The next step is to fix a galvanized mesh of 50x50 mm in size for the feeder. With the help of screws fasten the mesh on the side, in the front we leave a hole to load the hay.
  • Next, we build a small grid-rabbit connector that separates 2 cells on each tier in the middle. Measure the mesh size 25x25 mm and attach it with screws. You can also use boards or a piece of plywood to split these cell sides.
  • Doors can be made of wooden beams and stretched on them a galvanized small grid. You can just knock them down from the brusks of the tree. Be sure to use good door latches so that the rabbits do not run away.
  • The final stage will always be the construction of the roof. She needs a material that tightens nicely into the already finished raccoon skeleton. Above is a sheet of slate, it is better to use wavy.
  • x

    https: //www.youtube.com/ watch? V = OIU9oJARVak

    Back to


    Professionals' Tips It is important to remember that it is not necessary to paint and process a cage because the rabbits will bite it.

    In corners, you can reinforce the insertion of iron corners so that the rabbits did not run away.


    Additional rabbit feeding equipment can be purchased at pet shops. You can use simple bowls for water and grain.

    In the winter frosts, a rabbit cage can be warmed up. On top of slate or plywood, put felting, heater, old blankets, fur coats, and under the wooden flooring on the grid, also put a heater. At the very cage, lay out a lot of hay, straw, and a twig. For rabbits, put special boxes, the rabbit itself will make them warm nest there. The door can be further trimmed with plywood to avoid cracks.


    Making a home for your pets with the right material and drawings is easy. The main thing, then, with trepidation and care, treat your animals, feed them in a special regime on time, inoculate them, give honeydew preparations for prevention in the spring and autumn, monitor the purity of the water in the drinkers and the availability of grain in the nurseries, pamper the summer with fresh juicy hay, and in winterharvested with dry grass.