Dumpor.com

Sanitary Engineering

How to collect a siphon for a sink independently?

If you decide to install and connect the sink yourself, you can count on success. Following the instructions, it will be much easier to do. These works do not require special skills and a large number of tools. The main thing - stock up with patience and give the

a bit of free time. So, how to build a siphon for a sink?

How to collect a siphon for a sink independently?

Siphon with overflow

The sink and sewage system are connected by a special hydraulic shutter, also known as siphon. There is an accumulation of water in it, which subsequently falls from the drain. Due to this adaptation, the premises do not get evaporation from the sewage system. Siphons from different materials are produced, and can differ in their design.

Unfortunately, the sink drain is periodically clogged, and if you do not immediately correct the situation, then the water will fall to the floor of the kitchen. To avoid this, install a siphon with overflow. With it you can without fear fill the sink with water( water from it will never pour).The overflow siphon is set in the same way as the other.

From which materials siphons are produced under the sink

For the manufacture of siphons different materials are used, for example, it can be plastic or metal. The metal( brass) siphon for sinking( chrome) is better to use in cases if you do not plan to install a stool "tulip", a closet or a cupboard under the sink. Since the metal siphon has a glossy chrome plated finish, it is not necessary to hide it. Coupled with some interior items, such as a mixer, dryer or pipes, a chrome-plated siphon will perfectly complement the design of the room. Keep in mind that chromium-plated coatings require special care.

In addition, siphons under the sink are bronze or copper. But since non-ferrous metals have the ability to oxidize, the practicality of such designs is not different. For the same reason, care should be taken more thoroughly and delicately in order not to leave scratches. Most likely, your choice will be based solely on the design of the room. If such equipment is ideally suited to your interior, it is unlikely that you will stop any warning. Indeed, this is worth it, especially since if you take care of the siphon right and in time, then it can last for quite a long time.

At present widespread plastic structures under the sink have been widely used. For what dignity this material has gained such popularity? You can see for yourself: by choosing the plastic siphon, you will pay for it at a minimum. With its assembly and installation, any home master can easily handle, even doing it for the first time. Mount plastic construction may even be in the most inaccessible place. In addition, this material is light and strong enough, resistant to chemicals, and, importantly, its properties do not allow the formation of lime plaque.

How to collect a siphon for a sink independently?

Three types of siphons with overflow of

There are three types of siphons under the sink: corrugated, bottle and pipe siphon.

  • One end of the corrugated pipe is connected to the sink, the other side is attached to the sewer. Between the two joints the pipe has a curved shape. Such overflow serves as a water closure, blocking sewage evaporation with unpleasant smells.
  • Bottle is not overfilled. It has a hole, its shape resembles a bottle. The water in such a hydrocarbon is constantly accumulating, and its discharge provides the same special hole.
  • In the pipe siphon, as in the first version, as a water seal( overflow), a curved form is used.
  • To assemble the siphon for the sink yourself, you need to know which elements of the construction must be present and what function each part performs.

    What is the siphon for a sink and how to assemble it

    As mentioned above, the siphon installation process does not require special skills and specific tools. It will be enough to prepare:

    • pliers;
    • sharp knife;
    • screwdriver;
    • sealant.

    All these tools are usually available to every husband in the house.

    The first thing to begin with when collecting a siphon is a protective grille to which the rubber gasket attaches. Further, the sinks are connected to the drain.

    The sink and the side of the outlet pipe must be separated by a special gasket of at least 3 mm thick. Keep in mind that the quality of rubber should inspire undeniable confidence. To ensure a reliable waterproofing material should be as dense as possible. If the gasket meets all of the above requirements, sealant is not needed here.

    By tightening the pipe to the sink, it is necessary to screw in the nut( which is in it) the connecting screw, it is done through the protective grid. To do this, you will need a wide screwdriver, because in diameter the screw is up to 8 mm.

    The nut nut is installed on the outlet pipe, then the gasket in the form of a cone is fastened. The bottle siphon is inserted into the nozzle and screwed with a nut at the height you want. At the bottom of such a siphon is a rubber gasket, and only after that it is screwed up to the body.

    Connect the siphon to the sink and drain pipe with a specially designed nut, without forgetting the tapered gasket.

    Convenient when siphon diameters are 50 mm, as in other cases you will need a connector adapter. It is not included, so you will have to buy it separately. Gasket in this case is not required.

    How to collect a siphon for a sink independently?

    What should you know to collect a siphon for a washbasin?

    If you are interested in how to properly assemble the siphon, pay attention to some details. First of all, when buying a kit, carefully check it for all the necessary items. The classic drain consists of the following parts:

    • protective grille;
    • rubber seal;
    • outlet pipe;
    • drain-out;
    • connecting screw;
    • coupling nut;
    • body itself;
    • pulling nut;
    • drainage;
    • cone-shaped gasket;
    • nut;
    • rubber gasket;
    • siphon lid.

    No less serious about the quality of parts, especially for gaskets. It is better if you do without silicone. In addition, keep in mind that it is better not to use the sealant, since when the situation arises, the siphon will open very hard.

    Check that the siphon has a drainage hose for the hose that will be required to connect to the dishwasher or washing machine duct. After you finish installing the siphon under the sink, be sure to test the design. You can do this, for example, by putting a newspaper in a sink, which should remain completely dry after you turn on the water.

    How is a sink with two plums going to be? Such a shell is called steaming. Her collection is a little different from the previous one. Is it that every step of assembly should be performed twice. Two sockets will be needed for the sink and the side of the outlet pipe.

    A bit about automatic rain. Many models of siphons for sinks are provided with free-wheel drive. Convenient such design is that in order to open the cork, it is enough to click on a protective grid. Each kit is accompanied by a detailed instruction manual and a step-by-step instruction describing the assembly of the siphon for washing. Serious difficulties in this case should not arise, the main thing - to keep the tightness of all compounds.