Soothing rosaceous hearts in a cold way - a recipe, a photo, an instruction
- 28 Sep 09:45
We continue to show how it is possible to use the technique in the
soap from zero in a cold way. This time we have an irritated heart
with a glitter!
The secret of such cool hearts in coloring multicolored
drops of soap mass on the surface of the main soap. Then
covered with a glitter layer. The main cute we have a creamy
shade that is achieved by adding titanium dioxide. About the
technique we used to say here( working like a soap
from the ground in cold way and from the base).
To be nice, you need a lot of time and
"thin trace".If soap gets too dense, then
will not be able to make small pretty hearts from the points. To maximize
to inhibit soap formation, we will use the following oils
: rapeseed, rice and apricot oil. We do not use
olive oil, because we want to make as much white as much
- A 18-piece soap form( photo).The dimensions of 32cm x 24cm x 6,4 cm
( data transferred from inches)
- 6 bottles
- pastry apricot oil 15 oz 15 oz
- Rapeseed oil Coconut oil 15 oz 15 oz
- Palm oil
- 11.3 ounces of rice bran oil
- 3.7 ouncesshea
- 10.2 ounces of sodium hydroxide( lye)
- 24.8 ounces of distilled water
- 3.8 oz Flavor "Beach breeze"
- titanium dioxide pigment
- -colored bubble Gum
- pigment orange pigment
- bright orange yellow pigment
- Green pigment
- Pigment blue, ultramarine
- Mica purple
- Sticks for creating swords
If you have never done soap from scratch, we recommend reading
this article. The lesson is designed for experienced
Be sure to wear the protective shield: goggles, gloves,
tight shoes. Do not allow children, animals to work.
The room should be airtight.
Preparation of colors for
soap To completely dissolve the titanium dioxide in a mile, we recommend that the
be diluted in oil beforehand. Then prepare the cups for the
colors - add 2 tablespoons of vegetable oil
( sunflower) and 1 teaspoon of the dye as pictured below.
Use a mixer to mix the mixture to a homogeneous
Then pour the color into each prepared bottle according to the
• The first bottle( red / pink).0.5 tablespoon pigment
Bubble Gum + 0.25 tablespoons pigment burgundy
• Second bottle( orange).0.5 tablespoon bright orange
pigment + 0.25 tablespoon yellow pigment
• Third bottle( yellow).1 tablespoon yellow pigment
• Fourth bottle( green).0.5 tablespoon green
• Fifth bottle( blue).0.5 tablespoon blue pigment
• Sixth bottle( purple).0.5 tablespoon purple
Carefully and slowly add alkali to water and carefully mix
with alkali to complete dissolution and transparency. Put
in the side for cooling.
Melt and mix base oils. Once the alkaline water and the
oil are cooled down to 80 degrees Celsius or below( ideally, the
should not exceed 3-4 degrees Celsius), slowly pour the water from the
into the oil and mix it with an
"fine trace".If you want a piece of soap to be harder and the
can be quickly absorbed from the form, we recommend adding
sodium lactate to a cooled mixture of water and alkaline. For this
recipe, we added 4.5 teaspoons of sodium lactate.
After achieving the perfect "track" to prevent further strictly not
is recommended. Now, in each bottle, measure 2-3 ounces of
( 60-80 m) mixture and pour in them.
Now tightly close the bottle and mix a strong cocktail,
as a bartender =) Naturally, repeat this for each color.
For the remaining uncoloured mixture, add 2 tablespoons of
titanium dioxide and flavor. Use a rod for
to mix ingredients.
Pour white soap into the mold. Shake the hand at the edges so that the
releases excess air from the mixture and does not form bubbles.
Now check the cups in bottles. If the soap becomes thick, then the
spray the bottle. Hurry up! After all, at this moment, the white soap
also begins to solidify.
Then, apply droplets on the surface of a white soap with
using a bottle, as in the photo below.
You can do any order and not adhere to the strict
space between the dots. Still soap making is
Now take an ordinary thick stick( or any other
object) and start connecting these points with each other from one
angle to the other( as pictured below), without breaking to the very last
point. Try not to touch the white base so that the droplets of the
do not fall apart.
And continue in the same vein.
Now pour a cute glycer and then spray with an
alcohol sprayer to prevent the formation of
soda ash( otherwise it will look like you shed the
soap with no glitter, but with baking soda).Now cover the
with a wooden lid and towels and let it stand for 24 hours.
Then remove the lid and give 3-4 days for the cute
to solidify. The soap process will be
long, due to soft oils, but it's worth it! After that remove the soap from the form,
cut into pieces and let it ripen for 4-6 weeks.
Note. If you have so much left in bottles, then the
offers them to fill in other forms - let these
residues serve in everyday life!