Dumpor.com

Household

Apertures, cages for your hair with your own hands: drawings, video

For successful breeding of any animal it is necessary to provide it with good conditions. This rule is particularly relevant to the maintenance of sodium because these animals have some specific needs that they need to provide. Therefore, it is necessary to consider in detail the cages for

, which will be the most suitable for the animals to feel well.

Apertures, cages for your hair with your own hands: drawings, video

Article content:

  • 1 Cell requirements for successful dilution
  • 2 Preparation of
  • materials and tools 3 Preparation of
  • frameworks 4 Mesh assembly
  • 5
  • plywood layer 6 Ceiling
  • 7 Summary

Requirements for cells for successful dilution

Nutrition is wildlife, thereforeshe loves space and its content in very tight spaces, nothing good will lead. Many breeders prefer to make cells for nutria with their own hands. This is due to the fact that the purchased houses for nuts are made only of mesh, and in winter they are too cold, and in the summer they are very blown by the wind.

When you make a home for rodents yourself, you can apply not only a grid, but also a layer of heater, which will solve many problems. Such a cell with its own hands can be installed outdoors from spring to autumn. At home, when the mass content is more seasonal in nature, and only producers remain in the winter, the ability to hold the stock on the street is simply irreplaceable.

Apertures, cages for your hair with your own hands: drawings, video The scheme of a variant of a cage for a root with a pool: 1) a pool, 2) a descent, 3) a walk, 4) a house

If even a small cell, in summer in it it is possible to contain a lot of animals after having completed a cage for nutrium. Spacious walk will solve the problem of crowding in the house, where rodents will sleep. It is also good to make such a collapsible cage to make it easier to transport.

Apertures, cages for your hair with your own hands: drawings, video You can make a small and a large cage - it all depends on how much you hold

. Preparation of materials and tools

With the most simple joinery tools you can make comfortable cells, which will be arranged not only by the breeder but also by the animals themselves. Just keep in mind that the house must withstand the attack of the acute teeth of these rodents, so that the usual box with the door safely destroyed.

The following materials are used for building the cell:

  • wooden rack 50x50 mm;
  • sheet plywood;
  • insulation in the form of foam or foam polystyrene 40 mm in thickness;
  • steel wire mesh for walls with wire thickness of 3 mm and a cell 2-3 cm.
  • flat slate;
  • tin or zinc coating;
  • specialized grid for flooring with a 0,8 mm hinge;
  • nails;
  • screws;The
  • kit has a curtain on the door.

The minimum set of tools should include:

  • woodcutter;
  • pencil;
  • ruler;
  • Roulette;
  • building corner 90 degrees;
  • Drill with Drill;
  • cross-shaped screwdriver;
  • metal cutters or scissors;
  • hammer.

Apertures, cages for your hair with your own hands: drawings, video Drawing of one of the variants of a cage for a nut: 1) a walk, 2) a door of a walk, 3) a house

Preparation of a frame

The proposed type of a cell not only easily opposes the teeth of animals, but also has good thermal insulation parameters, which helps to save heat in winter andCoolness in the summer. This cell structure for nutria is still not suitable for year-round outdoor maintenance. In the winter, it needs to be put in a shed or a specialized room, and if it is not heated, then rodents will feel much more comfortable than in pure cellular cells.

In the special literature, there are many drawings of cells that are designed to hold different individuals. The proposed design is suitable for females with brood. External dimensions 90x100x60 cm. The design is simplified and does not include a stationary pool and a private house.

To begin with, a frame made of a rack of 100 cm in length, 90 cm in width and 60 cm high, is manufactured. It is necessary to control that there is a straight angle between the cross beams. If, after assembly, the structure is fluctuating, then it is not scary and after the installation of walls, the leftover will disappear. Do not use metal corners to fix the rails with each other, because in the future they will interfere with the installation.

Before punching a nail or screw, it is important to drill holes with a diameter smaller than the fastening thickness. If you kill the mount in the face, then the hole is optional, as the tree in this place is not prone to cracking. When working there is no need for complex joiner's joints, such as a spike and groove, since the walls will significantly strengthen the design.

After building the frame for the nutria, you need to choose a convenient place for the door on the front wall. Its sizes are chosen only at will, it can be, both on the whole wall, and on 40-50 sm. Having determined the parameters, it is necessary to install vertical bars, which will become a door box.

Apertures, cages for your hair with your own hands: drawings, video A detailed home cage circuit for breeding and maintaining the

mesh Installation of the

grid Next, you can go to the grid installation. First, you should fix it on the floor. The net is nailed only from the inside of the cell, this eliminates the possibility that the nurtures can tear the rack. If your net fixes badly, then it's not too late to add a few cross-sections from the same bar to the bottom of the frame. Two strips 30 cm from each edge will make the design as reliable as possible.

Then you can go to the walls. The net on them is also fixed from the inside. For convenience, you can be nailed to the front wall without cutting the window under the door, and do it already after the installation using the cutters.

Plywood layer

When the bottom and side walls are completely covered with a grid, it is necessary to make a sheath. It is carved out of plywood and heater. It is mounted only on the rear and side walls. For this purpose, plywood is cut from the plywood, which in size is in the frame between the rails. Having prepared three sections, two identical for the side walls and one wide for the rear, you can begin to install them.

For this plywood is placed in the gap between the frame, close to the grid. Its fixation is optional. Then the foam or foam polystyrene is cut the same size and is inserted from above. He is also not fixed. After this, plywood or galvanized metal is cut on the external wall dimensions, and tightly tucked along the path to the rails. It turns out a multilayered wall with:

  • mesh;
  • plywood;
  • heater;
  • exterior plywood or galvanized.

Apertures, cages for your hair with your own hands: drawings, video Laminated plywood sheets for manufacturing

Cell

Ceiling Doing so with all the walls you can go to the ceiling. To do this, you need to cut a flat slate on the size of the internal passage between the rails of the ceiling, similar to the first layer of plywood for walls. At a distance of 1 cm from the edge of the rails, along the contour parallel to the bottom, you need to screw the screws in a step of 30 cm, without pressing the bonnet to the end. The resulting plane holds ceiling slate. Next is a heater and is covered with a large sheet of slate, wave or flat.

This solution is ideal for use at home, because if you need a transfer, you can remove the upper ceiling, heater and slate. The cage will immediately become lighter half. The design is practically ready, only simple doors on the curtains need to be made.

Summary

The proposed cell maintains a comfortable temperature in summer and winter. It needs to install a water tank for swimming. A fine mesh on the walls prevents the grinding of plywood. All materials are fairly light, and taking off the roof, an empty cell can carry even one person. If the female living in it will give birth, then it's enough to set a box away from the desk or cabinet. It will be enough for it to build a good and warm nest for the kids, and watch them can be without opening the door.

The advantage of this construct-cell for nutria is also that even on the edges of the residential part below is a grid, not a rack, so the dirt will always fall down. As legs at home, you can use ground-nailed pegs, wooden logs or timber, screwed around in the corners. Here's just how easy it is to use inexpensive materials to make a lightweight and mobile cell for the maintenance of sodium.

Apertures, cages for your hair with your own hands: drawings, video Video